Unveiling structure and performance of tea-derived cellulose nanocrystals.

In this study, cellulose was extracted from black tea residues to produce black tea cellulose nanocrystals (BT-CNCs) using an optimized acid hydrolysis method. The structure and performance of BT-CNCs were evaluated. The results showed that the optimal conditions for acidolysis of BT-CNCs included a sulfuric acid concentration of 64 %, a solid-liquid ratio of 1:18 (w/v), a hydrolysis temperature of 45 °C, and a hydrolysis time of 50 min. The optimization process resulted in a 44.8 % increase in the yield of BT-CNCs, which exhibited a crystallinity of 68.57 % and were characterized by the typical cellulose I structure. The diameters of the particles range from 5 to 45 nm, and they exhibit aggregation behavior. Notably, BT-CNCs demonstrated excellent storage stability, and the Tyndall effect occurred when exposed to a single beam of light. Although the thermal stability of BT-CNCs decreased, their primary thermal degradation temperature remained above 200 °C. The colloidal nature of BT-CNCs was identified as a non-Newtonian fluid with "shear thinning" behavior. This study introduces a novel method to convert tea waste into BT-CNCs, increasing the yield of BT-CNCs and enhancing waste utilization. BT-CNCs hold promise for application in reinforced composites, offering substantial industrial value.

Development of a self-reinforced starch-derived film with biocompatibility and mechanical properties.

The scraps produced while processing packaging materials will cause a waste of resources. In this study, starch-based self-reinforced film (SSRF) using thermoplastic starch (TPS, 45 wt%) and polypropylene (PP, 53 wt%) was developed. The effect of extrusion times (1-4 times) on the film structure and performance was explored. The results show as the number of extrusions increases, the color of SSRF deepens from gray-white to brown, and the crystallinity increases. The mechanical properties of the four types of SSRF first increase and then decrease. The 2-SSRF has the best performance, with tensile strength of 13.23 MPa, elongation at break of 61.35%, Young's modulus of 1128.99 MPa, and flexural strength of 33.19 MPa. Proper extrusion improves the compatibility of TPS and PP. However, repeated extrusion will cause PP degradation and TPS carbonization, reducing interfacial interaction. This study developed new starch-based self-reinforced film and provided theoretical guidance for reusing packaging material scraps.

Starch-based biodegradable composites: Effects of in-situ re-extrusion on structure and performance.

In this study, starch-based biodegradable composites (SDC) were prepared by extruding using thermoplastic starch (TPS, 65%wt), polylactic acid (PLA, 30%wt) and poly (butylene adipate co-terephthalate) (PBAT, 5%wt). Structure and properties of the SDC were compared by performing 1-, 2-, 3-times extrusion. The results show that in-situ re-extrusion refines the TPS in composites and reduces the size of the phase. As the number of extrusions increases, the ester bond of composites at 868 cm-1 disappears, the crystallinity increases, and the thermal stability decreases. Among the three types of composites, the mechanical properties and hydrophobic properties of the material obtained by the 2-times are the most outstanding. Compared with SDC, the elongation at break and Young's modulus of SDC-2 are significantly increased, with an increase of 8.01 % and 1.28 % in the machine direction and an increase of 11.02 % and 1.79 % in the transverse direction respectively. Additionally, water contact angle range of SDC-2 from 98.7° to 101.7°. Therefore, SDC prepared by 2-times in-situ re-extrusion has the best film properties and is an ideal packaging material. This study presents a novel method for fabricating starch-degradable composite films by in-situ re-extrusion, providing new insights into the development of starch packaging materials.

Effects of crosslinking agents on properties of starch-based intelligent labels for food freshness detection.

The impact of citric acid, carboxymethyl cellulose, carboxymethyl starch, sodium trimetaphosphate, or soybean protein on the crosslinking of starch-based films was examined. These crosslinking starch films were then used to create pH-sensitive food labels using a casting method. Blueberry anthocyanins were incorporated into these smart labels as a pH-sensitive colorimetric sensor. The mechanical properties, moisture resistance, and pH responsiveness of these smart labels were then examined. Crosslinking improved the mechanical properties and pH sensitivity of the labels. These different crosslinking agents also affected the hydrophobicity of the labels to varying degrees. Soybean protein was the only additive that led to labels that could sustain their structural integrity after immersion in water for 12 h. Because it increased the hydrophobicity of the labels, which decreased their water vapor permeability, moisture content, swelling index, and water solubility by 47 %, 29 %, 52 % and 10 %, respectively. The potential of using these labels to monitor the freshness of chicken breast was then examined. Only the films containing soybean protein exhibited good pH sensitivity, high structural stability, and low pigment leakage. This combination of beneficial attributes suggests that the composite films containing starch and soybean protein may be most suitable for monitoring meat freshness.

Characterizations and film-forming properties of different fractionated high-amylose maize starches subjected to hydroxypropylation.

Dual-modifications of jet milling and hydroxypropylation were used to improve the functional properties of maize starch (HM, containing 67 % amylose). The fractions obtained in three sizes (HM-S, HM-M, HM-L) were further treated with 10 % and 30 % propylene oxide (PO10 and PO30). The infrared peak of starch at 2794 cm-1 indicated the successful introduction of hydroxypropyl groups. The molar degree of substitution (MS) increased with the degree of jet milling. The MS of HM-L-PO10 is 0.4, that of HM-M-PO10 is 0.7, and that of HM-S-PO10 is 0.9. The crystallinity of dual-modified HM increased, but the crystal type remained unchanged, still being B-type. Dual-modification significantly improved the performance of starch, and the higher the degree of modification, the better the optimization effect. The lowest enthalpy changes of gelatinization (ΔH = 3.49 J/g), the best freeze-thaw stability, the highest elongation at break (110.42 %) and transmittance (81.22 %) were shown in HM-S-PO30. The present study confirms that HM-S-PO30 films have the best physicochemical and mechanical properties, which provide new insights into optimizing starch-based packaging materials.

Progress on molecular modification and functional applications of anthocyanins.

Anthocyanins have attracted a lot of attention in the fields of natural pigments, food packaging, and functional foods due to their color, antioxidant, and nutraceutical properties. However, the poor chemical stability and low bioavailability of anthocyanins currently limit their application in the food industry. Various methods can be used to modify the structure of anthocyanins and thus improve their stability and bioavailability characteristics under food processing, storage, and gastrointestinal conditions. This paper aims to review in vitro modification methods for altering the molecular structure of anthocyanins, as well as their resulting improved properties such as color, stability, solubility, and antioxidant properties, and functional applications as pigments, sensors and functional foods. In industrial production, by mixing co-pigments with anthocyanins in food systems, the color and stability of anthocyanins can be improved by using non-covalent co-pigmentation. By acylation of fatty acids and aromatic acids with anthocyanins before incorporation into food systems, the surface activity of anthocyanins can be activated and their antioxidant and bioactivity can be improved. Various other chemical modification methods, such as methylation, glycosylation, and the formation of pyranoanthocyanins, can also be utilized to tailor the molecular properties of anthocyanins expanding their range of applications in the food industry.

Improving properties of normal maize starch films using dual-modification: Combination treatment of debranching and hydroxypropylation.

Structure and properties of films made from native, debranched, hydroxypropylated and debranched/hydroxypropylated normal maize starches were determined and compared. The modified starch films were much smoother and more integrated than native starch film. Especially, the particles were not observed in dual-modified starch film but in debranched starch film, which might result from amylose recrystallization. Debranching substantially decreased elongation at break of starch films from 39.2% to 8.4% and hydroxypropylation decreased tensile strength from 4.82 to 2.92 MPa, indicating neither debranching nor hydroxypropylation could comprehensively improve the film properties. After dual-modification, elongation at break and tensile strength of the film were increased to 57.2% and 7.35 MPa, respectively. Moreover, the barrier performance of films was in the order of hydroxypropylated starch film < native starch film < dual-modified starch film < debranched starch film. It was suggested that dual-modification could be an effective approach to obtain starch films with tailor-made properties.

Improving the properties of starch-based antimicrobial composite films using ZnO-chitosan nanoparticles.

This work dealt with the antimicrobial nanoparticles and incorporated them into the modified starch matrix to prepare composite films. The ZnO-chitosan nanoparticles with 57.3 wt% ZnO were sol-gel synthesized for formation of hexagonal phase. The absorption peak and average size of nanoparticles was approximately 364 nm and 25 nm, respectively. It was observed that nanoparticles with less than 3.0 wt% were homogenously dispersed in the starch matrix. The increase of nanoparticles in films resulted in a substantial reduction of water vapor permeability from 51.0% to 43.7% accompanied with an increase of tensile strength from 4.11 to 12.79 MPa (p < 0.05). Moreover, higher addition (4.0-5.0 wt%) resulted in aggregation of nanoparticles in films and increased water vapor permeability (p < 0.05). The antimicrobial activity of starch-based films was positively correlated with the loading level of nanoparticles, and these films had stronger suppression in Gram-positive S. aureus than Gram-negative E. coli.